See my latest video. Not much new, but the first time to see the completed prototype.

I will be creating a tab with all of the files required for this version of the watch. The two versions are:

v1: With thumb wheel and GY-80 IMU. (will not fit in iPod nano case, but you can use the backlight made for the display. Also no board mounted piezo speaker - but hookup pads available)

v2: With 3 micro pushbuttons and discrete chips for IMU and Pressure sensing and board mounted speaker. (will fit nano case)

Final Prototype (Yeah, right)

Here is the assembled watch in it's case.

Note, I changed the watch face from the previous prototypes. You know why? Because I can!! I love having a watch that is totally customizable.

This current version is different from the last because, instead of using an IMU board with the 3.3V power supply and the sensors, I have used discrete components. This has reduced the thickness to be able to mount the whole project in the iPod nano case. Well, almost. The battery is sitting on the outside of the case but adds so little to the width it is nearly undetectable. Here is the new assembled board:

The small square to the right of the ATMega1284p is the LSM9DS0 IMU chip and just to the right of that (the small silver looking square) is the BMP180 Pressure sensor. Note that I had to take part of the case off of the piezo speaker (large square on top of board) so that it would have the clearence needed to slide the case over it.

Here is the case going on:

Next, I position the battery and tape it down:

That is it. Place the band on and you are good to go.

Notice the profile. The battery is almost invisible.

That is it. You have an assembled watch. I will be posting a video soon. I have a couple of the blank pc boards for this project, so I may make them available to anyone looking to take on this project. All components come from Mouser and I will post the parts list when I post the updated schematic and layout files.

If you like this project, please like the post and share it with your friends. And don't forget to vote for it in the Atmel Simply AVR design contest!!! Thanks so much!!

I posted an updated video of the prototype watch. Go see it in action.

Final look

Here is a picture of what I am going for. This is my first prototype (with the sensor board removed) in the Apple Ipod Nano Aluminum Watch Band.

Really pretty. But here is the thing. It is tight in that case. The Ipod Nano 6th gen is tiny!!! I have the battery for it next to the watch in the picture and you can see that it takes up half the volume of the compartment. To make this all fit and still make it so it can be a hobbyist project may be a little much. The piezo speaker I got in from Mouser is only 3mm tall and is way too big for the housing. It will also be tough for the battery to slip in on top of components mounted on the board. I have a couple of options. I can make the watch a little thicker and stay with the rubber case which is pretty forgiving, I can strip the watch down a bit to fit in the nice rugged case, or I could try to fabricate a custom case for it. I am leaning toward the rugged case. I think the next watch will probably be a redesign using a Sharp Memory Display and a dedicated power management chip. I may also go with an ARM processor. I will update as this unfolds.

Battery voltage measurement

I have been thinking about the battery voltage measurement. There are many trade offs in the different methods to accomplish this. The voltage divider I have now works fine. In a voltage divider, the lower the resistance values, the better resolution you have, but the more current you draw. I use 100k ohm resistors so the total current draw (continuous draw) is 20 micro amps. This doesn't feel really good as the Atmel mega1284 can power down to about 1 microamp. The alternative is to add a switching circuit like a FET to switch on the power to the voltage divider. This would make the current draw almost zero when not in use, but adds to the complexity of the board layout. I think for the current version I am going to go with the simple voltage divider and suck up the current draw. After all, the lcd is drawing about 250 microamps anyway and my goal is really to stay below half a milliamp in idle mode. For later models I will consider some of the new battery monitors/manager chips out there. They are good at not only reporting voltage but tracking battery capacity to give you a better idea of remaining battery life. Parts arrived from mouser (particularly the small switches I need) so I will be finalizing the design of the next version. As much as I hate it, I will probably leave out the Bluetooth at this point because I really want this to fit in a good looking case. Stay tuned for updates.

Using the Watchdog Timer for Periodic Tasks

The more I read the datasheet on the mega1284p the more I am amazed at what I learn about chips I have been using for a long time. Forget about using timer 2 for your periodic tasks. It is nice because it can continue to run in sleep mode but it is only an 8 bit counter. Even with the max prescaling (1024) with my 8 Mhz clock you roll over about every 0.03 seconds. This forced me to keep a counter running to only update my clock every 1 second or so because the overhead of doing it every 0.03 seconds crashed the processor. Then I read the section on the Watchdog Timer. I have used it before to reset the processor when my code hung up, but I learned that the WDT can be used in interrupt mode only. This means I can use it for the periodic functions. And the great part is it has it's own clock source which will allow it to roll over from 16ms to 8 seconds. And this leaves Timer 2 for other Arduino functions or I can bring the chip down to lower shutdown levels to conserve battery power. You have to use a timing sequence to enable the WDT, so after some searching and tweaking, I found the following to work:

// Setup the watchdog timer to overflow every 8 seconds.
  MCUSR &= ~(1<<WDRF);
  WDTCSR |= (1<<WDCE) | (1<<WDE);
  WDTCSR = 1<<WDP0 | 1<<WDP3; // Set Watchdog Timer to interupt on 8 second overflow
  WDTCSR |= _BV(WDIE); // Enable Interupt but not Reset

That was it. I then used the Interrupt service routine to set my update flag ( the interrupt caused the chip to wake up from sleep)

SIGNAL(WDT_vect){
  //Add periodic operations
  if (mSelect == -1) clockUp = true; // The current mode is the clock, otherwise, don't update
}

I am currently optimizing the code to minimize battery power. I have it down to about 0.6 ma in sleep mode. The lcd should be about 0.25 ma. Unfortunately, the rest is mostly the stock IMU board. Even placing the individual components in low power mode, it is still a big draw. I am going to fix that in my next design by replacing the board with a BMP180 and a LSM9DS0 IMU. These should virtually disappear in low power mode and the 0.25 ma for the display should be just about all I see. That will give about 16 days of standby time for the 100mah battery I have. I have ordered the final parts from Mouser and will finish the PC board layout after they arrive. The new design will have the improved IMU, barometer, bluetooth, an installed speaker, and I hope, will all fit in the LunaTik ipod nano 6th gen watch case to make this project truly wearable and good looking. Stay tuned.

Board Layout:
Board Layout (*.brd)

Schematic:
Schematic (*.sch)

Arduino Sketch (zip):
Arduino Sketch (*.zip of all tabs)

These files will give you a good idea of how I constructed the watch. Note: these are still all in their early development stages and do not have a lot of polish or annotation.

First 2 Prototypes Completed

I made a couple of design changes to the protoype watch in my YouTube video. I now use an EADOG-102 lcd and this prototype will not have Bluetooth. I also switched to the ATmega1284p. It is Arduino compatible and has 16k RAM!!!!!!!!!   Here is the new system laid out on a breadboard:

I got my circuit boards from SeeedStudio's Fusion service the other day. They look really good (the boards not my terrible silk screening skills). It was a great deal. I paid $10 for 5 boards and $7 for shipping. They were cool enough to send me 6 boards (probably because my boards were so small they couldn't utilize the space for anyone else - but that is way cool they did that) and it took about 3 weeks from submission to arrival.

I was going to use a work light and low temp solder to assemble the boards, but based on the good job on the spacing in the layout, I decided to hand solder the first prototype.

I soldered the components up to the sensor assembly and the lcd.

At this point, I want to power up the ATmega1284p and see if it will receive the Arduino bootloader.

Here is where I learned a lot of things I already knew. I initially tried to bootload using an Arduino as the ISP. When I tried to load the 1284p 8Mhz bootloader, It started to go and then hung up. If you notice in my schematic, I decided to use the internal RC oscillator to save component count on the board. The first thing that the Bootloader does is set the fuses to predetermined values. That caused the 1284 to switch to external 8Mhz crystal. I don't have one so the chip became unresponsive. When I realized what I did, I simply soldered two leads to the 1284p pins for the crystal, attached an external 8Mhz crystal and was able to use AVRStudio to reset the chip to use internal oscillator. I used it to load the bootloader too. At this point, I put 3.3V to the board and held a FTDI programmer to the programming port and uploaded the firmware from the Arduino IDE. I was both happy and amazed it worked.

Now that that was verified, I soldered the sensor board and the lcd. The result was the completed prototype.

I specifically designed the size to be able to fit perfectly into the numerous rubber watch cases available for the ipod nano. This one was $3 from Amazon. 

And the final assembled watch.

Right now, the watch has modes to display weather data (temp/press/altitude), Accelerometer data, Magnetic field data, I have a mode to set the time. I can view the status page and check remaining RAM (which I have over 14k - thanks 1284p!) and the status of the RTC and sensors, I can set the contrast and 12/24 hour time mode and check the battery voltage too. I have not implemented the Gyro data yet (the gyro is the biggest power hog) and I did not add a speaker to this yet (I have pads for it on the pcboard) and there is no Bluetooth although the FTDI connector has all the connections I need to implement a small transceiver. 

I finished a second prootype using the special backlight available for the EADOG-120 display. It adds significant width (backlit watch is twice as wide as non) but it is a pretty cool feature. Since the display uses two different sets of lights, I tied one to the 1284p and the second I hardwired to the battery. This lets me use the backlight without having to wake up the microcontroller, but still gives me software control of the the backlight if I want it constantly on or want to use it as an alarm mechanism. The lcd without the backlight is the one that has a special back that can't be used with a backlight but is really readable in ambient light.

With the massive RAM I have I intend to make the displays more attractive, add animations, and track trends in pressure to forecast weather. I will also add some specialty apps to uttilize the accelerometer as a movement alarm and a golf rangefinder (hold watch at eye length, point your finger at the bottom of flag, then at top, use the orientation data to calculate distance to pin). I will also use the clock display to show more data like battery status and pressure trend.

I would encourage Makers to have at my designs, modify them, improve them, and build your own smart watch. I am working on another version using the 1.3" oLed display. It will not use the sensor board but will be constructed with discrete sensor components. It will also have a USB port for recharging.

Thanks for reading. Hope this has motivated you to try a project like this.

Here is the schematic.

Arduino Smart Watch

This blog will catalog the work I am doing to create an Arduino-based Smart Watch. See the below video for an introduction on the concept.

 

 

I submitted the project to the Atmel Simply AVR Contest. See Below:

ATMEL Simply AVR Contest

 

I have modified the project to use the EA DOG 120 LCD display instead of the oLed for now. For one, it is super easy to use, very thin, and has pins that fit a breadboard. It is very low power and always on as opposed to the oLed that I want to leave off. I am working on an oLed watch too because I happen to love the look of the 1.3" oLed display.

 

For the project, in order to make this so the average hobbyist could construct it, I have decided to use the GY-80 IMU as the sensor platform. It has the BMP085 Pressure/Temperature sensor, and accelerometer, gyro, and magnetometer in a very small form factor. It also has an on board 3.3V regulator. By using this board, I will cut out having to solder a bunch of very small components and save a lot of board space in the process. I had the pc boards made and they are on their way. I will update when I have assembled the first prototype.